• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have a unique procedure to add another key. This requires an electronic handheld computer, referred to as Tech-2 that is operated by the dealer. Then a new car key and transponder are required to be purchased and then programmed to the car.

Rotate your keys to prevent one from wearing out more than another. This will also help keep your keys in good condition.

Replacement Case

The new key fobs for keys are not like the old Saab fob key Replacement keys. They are equipped with electronics that make them difficult to copy. That has made car theft significantly more difficult than it was just a few years ago. However, it has made the replacement of lost keys a much more expensive task.

Every owner of a 9-3 Saab should have at a minimum two functioning keys. It is expensive to replace a lost or damaged key since it requires replacing the CIM module, as well as reconfiguring the locking cylinders. Dealers will typically charge $100-$200 to complete this.

There are a few ways to avoid these expensive. Some parts dealers will use the code of a spare key to cut a new metal blade for less than the price of the dealer. The key must be exactly the same as the original to allow it to function in your vehicle.

Follow these steps to replace the case. You'll need a flathead screwdriver as well as some patience. With the screwdriver, you can pry apart the plastic, and then take off the emergency key. Once you have the case open, remove the electronics and put them back into the new case. Make sure to insert the correct key and badge back inside the case, too.

Replacement Battery

The replacement battery for the saab ignition key 9-3 is a cheap component that can be replaced quickly and easily. This YouTube DIY video Cyclone Cyd will show you how to get a saab replacement key to replace the battery of the remote key fob in only four steps. This tutorial is suitable for any modern saab key fob though the process may vary slightly.

The first step is to locate the button that will release the backup key in the fob. It's usually next to the saab 9-3 key fob programming logo on the back of the fob. Then, use the flathead screwdriver to insert into the small hole in this button. This should be enough to allow you to open the fob case in order to change the battery.

After you have installed the CR1632 batteries, you can put back together your remote key fob. Then, you can program it into your car. The entire process should not take more than one hour. It's a simple procedure that doesn't require any special equipment.

If you lose your key, the procedure will be a bit more involved but it is still able to be completed. The dealer will need to read the car's VIN and then order a replacement key blade and TWICE module with the proper unique code. After that, they will have to cut the replacement key and then program it using a new software tool called MDI.

Key Replacement Fob

The key fob is the part that locks and unlocks your car, it's got batteries inside. Batteries have a finite lifespan and eventually die. This is a typical issue that happens with all cars, and the good news is that you can replace the batteries in most key fobs and not have to replace the entire case. You can buy replacement fobs on Amazon that have all the electronics already in place, so you'll just pop open the case and replace those batteries that are old. You'll need to take out the emergency key before you replace the batteries. To do this, place a small screwdriver that is flat into the slot in the middle of the. Move the screwdriver around the case until it will split open, making it much easier to remove.

When you're ready to replace the keys ensure you have a spare, because this can cut down the total cost by a significant amount. If you have an extra key, you can request the dealer to cut the key and program it for your vehicle. This is less expensive than purchasing a brand new key fob.

If you do not have a spare key car key, you can add a second key to your car, but it requires a lot of research and effort. It can cost a few hundred dollars to get an additional car key. The computer in the car must also be programmed. Professionals can do this, but it's an expensive option.

Replacement Ignition

The modern saab 93 replacement key 9-3 uses an advanced alarm system based on a key code. This means that when you lose your sole working key, adding another key can be extremely expensive since the car has to have a computer module added and it must also be specifically programmed to accept a new key. Even dealers can charge hundreds of dollars to program a new key if they are unable to do it.

If you've lost your sole working key the dealer will replace the computer in your car (known as the CIM or SAAB TWICE) in order to make the replacement, and will charge you the highest price for it. Instead we can reprogramme the EEPROM of your current car computer, preparing it to accept a second key, which will save you more than 50% of what you'll pay at a dealership.

If you've owned a SAAB 9-3 quite a while and you're aware of the ignition keys aren't very durable. If the ignition key you have isn't working correctly, you should consider replacing it. They can become sticky and the buttons can fall off. Luckily, replacing the ignition key isn't as complicated as it sounds and is fairly easy to do using the right tools.