• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, patio doors undergo wear and tear that could lead to lock malfunctions. There are a few basic steps you can take to ensure the security of your uPVC door.

These easy fixes will make your home safer, whether you realign the lock or clean the mechanism.

Clean the Lock

Although patio doors are a great option to let the outside in and keep the elements out however, they can also pose a security risk in the event that your lock isn't operating as it should. Over time, wear, tear, cold and hot weather dirt and debris can cause your patio door lock to become difficult to operate. With a little care, you can ensure your patio door's locks will always function correctly.

It is important to first clean the patio door lock and all moving parts. This will help remove any coatings or dirt that could be preventing your lock from functioning properly. Start by wiping the moving parts of the lock for your patio door with a wet cloth. Then apply a scouring pad or rough damp cloth to scrub the areas that are soiled of the door and frame. You should then wipe down the entire lock using dry cloth to get rid of any remaining dampness and let it to dry completely before using it again.

If your patio door is equipped with a pin-tumbler latch, you can apply powdered graphite to the key. You can also use a Teflon lubricant such as WD-40 Multi-Use Product. This kind of lubricant is easy to apply and it won't disintegrate over time. If you're unable to find the right lubricant to use with your lock, make use of a pencil with a more of a thicker tip. Put the pencil in the lock, then shake it around to spread the graphite.

Tracks for sliding patio doors require regular maintenance to keep them free of dust, dirt and other debris. These tracks are especially susceptible to ice, snow, and other debris, which can cause them get stuck or to bind. This could make it difficult for your patio door lock repairs door to be opened and closed.

Clean the track rails and rollers of sliding patio doors by removing any weather stripping that is damaged or dirty. Clean it and replace it. The rollers for patio doors can be cleaned and sprayed with an oil that is non-stick.

Lubricate the moving parts

uPVC french doors, like sliding patio doors, work by using 3 to 4 or sometimes 5-point locking mechanisms which include the lock cylinder and handle controlled by keys. They also require maintenance, including lubrication of the moving parts. This can be accomplished using a thin oil (never WD40) and should be done once per year.

If sagging hinges aren't the cause, the door could be misaligned and catching or striking the strike plate hole within the frame. Remove the strike plate and employ a sharp tool expand the mortise. This will allow the latch to fit into the hole and prevent it from rubbing against the frame.

Find the length of the cylinder using an object of book or wood that is able to fit into the space above the adjustment screw. The outer dimension is measured from the outside of door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the of the cylinder.

Check the width of the lock.

If your patio door latch isn't able to turn, even after cleaning and oiling it's possible that it is not aligned with the strike plate. Examine if the door is in balance and whether the hinge screws are tight However, in many cases, moving the strike plate up or down could fix the problem.

The most common issue is when the strike of the lock is too small for the latch to properly engage. In this case you'll need to expand the hole using either a hammer or chisel, and then test the latch to ensure that it connects to the strike plate without rubbing against or getting caught on the frame of the door jamb.

Before you purchase a replacement lock, first identify the type of mortise lock you have. This can be done by looking at the end faceplate and observing whether it is round or square. Take a look at each screw hole on the current lock and note their dimensions. This information will allow you to find the replacement lock that has exactly the same size and fits into your existing hole.

You'll need to locate the mortise lock and inspect it for any scratches, bends, or other damage that need to be repaired. A damaged or bent latch is more likely than one that's been used a lot to break. Replace the lock if you notice signs of damage.

Once you've identified the type of lock replacement that you require It's time to begin the actual repair patio door. The old handle and spindle must be removed from the doorway to the patio. Insert the new handle. Start by installing the interior handle. Align it with the spindle and then secure it into position using two screws or bolts. Once the interior handle is installed, put in the handle on the outside and screw it into place as well. Once you've completed these steps then you can test the new handles to ensure that they open and close easily and that the latch locks correctly when you strike the plate.

Check the door's Strike

The door latch and strike plate are two components of the lock that work to ensure the latch secures the door. If they are not aligned properly and the latch isn't latching the door shut correctly. Fortunately, this problem is usually easy to correct.

First, check the strike plate's receiving holes to make sure they are free of obstructions such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move vertically but not detaching it from the frame of your door. Adjust the strike plate to align its receiving holes with the latch hooks of the door latch. Once the strike plate is adjusted then tighten the screws and then test the door to see whether it shuts easily with the new adjustment.

Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, however they're essential for locking and unlocking your door. The metal plates are typically located on the top and bottom of the door jamb, where they support the door's latch. The door latch slides into the strike plate, and it creates a seal. If the strike plate has been damaged or rusted, or if it is not properly installed, the latch may not properly lock the door.

One common reason for a patio door lock to stick or not close is a misalignment of the latch and strike plate. The easiest method to check for this is by performing the "lipstick test." Rub some lipstick along the edge of the deadbolt, and then put masking tape on it. The lipstick will leave the mark when you close the door. This will indicate exactly where the latch joins the strike plate. If the mark is too high or low, you can easily adjust the strike plate.

If your patio door locks for sliding aren't working correctly, they can keep your home secure from intruders. It is imperative to resolve this issue as quickly as possible. Follow these steps to repair your patio screen door repair door lock and restore its function.