• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Door hinge a Loose Door Hinge

Fixing a loose door hinge is a simple task for most homeowners. If the screw holes have been stripped and will not hold screws, you could need to use wood glue and dowels to put back in the door hinge.

Before you do this, however, brush away the surface corrosion. This will help to keep the dowels in their place and provide a solid base to hold onto.

Eliminating the Hinges

A lot of door hinges are able to be removed, making it easier to move the double glazed door hinges from one side to the next or to remove the entire door off the frame, if needed. It is easy for anyone with patience, though you do need to know how do it right.

If the hinges have been painted it is necessary to remove it prior to trying to remove the pins. If you don't, the paint will be smashed off and scratch your door when you try to lift it. To break the paint seal, place the hinges in a stainless steel pan and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for about 30 minutes. The heat of the water will soften the paint making it easier to remove.

Once the pins are loose, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, however you should use a magnetic screwdriver for this task. This type of screwdriver was designed to grab screws made of steel and make the task speed up.

It is a good idea to spray some lubricant on the hinges before attempting to remove them. A simple lubricant can make the process move along quickly and make it easier to remove the screws and pins. You can find this type of lubricant at a variety of hardware and home improvement stores.

The number of hinges required will also vary depending on what type of door you have, and how it's set up. Heavier and solid-cored doors will require more hinges whereas lighter and hollow-cored bi-fold doors hinges may only require two or three hinges.

It is also important to understand the different types of hinges so you can determine which ones be the most effective for your particular situation. The hinges on the exterior are designed to support the weight of the door and interior hinges have to be able to support lighter loads.

Reattaching the Hinges

Over time, a door hinge can lose its grip and then begin to slide or hang crookedly. This could be a problem however, it's usually simple to repair. A simple retightening will usually solve the issue. However, if the screw holes have been stripped out, this may be more difficult to accomplish. Fortunately, there is a trick to get these holes back to their original size that uses a wood dowel.

Start by drilling the hole using a drill close to the size of the new screw (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a secure fit. Then, reinstall the screw and tighten it to the desired level of tightness. If the upvc door hinge replacement continues to have an tendency to get stuck, then add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to make sure that the clearances around the perimeter are correct.

You could also use a wood plug in place of the dowel. This will work just as well but might take a bit longer to set up. Simply whittle a chunk of wood that is the right size for a snug fit, and then insert it into the hole. If you don't have a woodworking tool, you can also try using toothpicks or wooden matches as well.

After you've reinstalled your new screw then use a countersink to make the hole for the head of the screw smaller so that it won't rub against the edge of the door when it's open and closed. This will make it much easier to tighten the screws before replacing upvc window hinges hinges.

After reinstalling the hinge, lubricate the hinge with an oil-based lubricant that is dry. This will help prevent it from getting stuck in the future. You can use products like PB Blaster and Liquid Wrench. You should apply a thin coat and allow it to take around 15 minutes to fully get into the barrel of the hinge.

Refinishing the Hinges

If you're not yet ready to replace your hinges, you can try a few simple fixes. The first step is to ensure that the screws securing the hinge plate to the door frame are tight. If they're loose, tighten them by using a drill or screwdriver. Be cautious not to tighten the screws so much that they begin to cause gaps at the trim joints, or worse, strip the threads.

If the issue is that the hinge plates are splitting and you want to reattach the plates by putting wood glue on the back of them and inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will serve as a solid base for the screws and help prevent the plates from shifting when you drive them into position. Allow the glue time to dry before you can reattach your hinge.

Another reason for hinges that are loose is that the screws are damaged or gone. This can be corrected by replacing the screws. Be sure to use a drill bit that is compatible with the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

Close the door once you've reattached your hinge and examine the gap between the frame and the door. The gap should be the thickness of a penny or less if the old door was not properly hung. This shouldn't be a problem if the hinges are properly installed.

If you find that the hinges remain loose, try putting a thicker hinge shim between the hinge plate and the mounting surface to add an extra inch of space. You could also try taking the hinge pin from the problem hinge and then pounding it with a hammer in order to make it more secure or using the hinge pin from a different angle altogether. It is also possible to lubricate the hinges with mineral or Jojoba oil to lessen friction and help them hold their place. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky and can also extend their life.

Cleaning the Hinges

The constant movement of a hinge creates friction, which draws dust particles. These particles may get stuck and accumulate over time in the moving parts of door hinges if they are not maintained and cleaned regularly. As a result, the hinge becomes stiff and creaky, and its appearance can be damaged quickly. Regular cleaning, lubrication, and inspection can help preserve the quality of hinged door and ensure their proper function.

Inspect the hinges to see how much rust has accumulated on their surfaces. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you are able to save the hinges, you should first clean off loose rust using steel wool and wire brushes. Apply a commercial rust removal solution or homemade solutions like lemon juice on the hinge. Let the rust remover be on the hinge for several minutes to penetrate and dissolve any remaining corrosion.

If you don't want to spend time and money to replace your hinges, simply retightening the screws will bring back the hinge's functionality. It is possible to attach an shim of wood or a dowel to the hinge when the screws have been stripped. Wooden dowels are round pieces made of wood in the shape of rods that are available in varying sizes and lengths. You can find them at home improvement centers, woodworking supply and craft shops, or online.

You can also make an shim out of either plastic or metal, depending on the type hinge you have. To make a dowel cut a piece of wooden dowel or other sturdy material to the desired size. You can then dip the dowel in carpenter's glue before inserting it into the stripped hole, allowing the glue to hold the dowel in place.

Before cleaning the hinges, put down a paper cloth or towel to protect your flooring from spills. After protecting the area then clean the hinges using a soft sponge or a cloth coated with mild cleaner to eliminate dirt and grime. You can also remove tarnish, dirt, and grime. You can make use of a toothbrush or a small brush to reach difficult-to-reach places in crevices and tight areas.