• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is a quick and cheap method to increase your home's security. However, this procedure isn't for all. It requires a certain amount of patience and expertise.

You must replace the cylinder that is inside the knob's body. The cylinder is what identifies the key when it's put into the lock.

Take off the lock that was previously used.

The first step to replace a door lock is to take out the window lock replacement that was previously in use. It is a fairly simple process, but you should keep certain things in mind. Make sure the new lock is compatible with your door. This will ensure it is securely fitted and won't create a gap around the deadbolt or latch.

Once you have removed the latch plate look for two screws or bolts on the inside of the casing, which hold the casing and the two halves of the lock together. Remove these screws with the help of a screwdriver, and then remove the lock from the door. If you have a mortise locking system, there is an anchor screw that connects the handle to the spindle. Remove the doorknobs by unscrewing this screw with the help of a screwdriver.

You should also take the deadbolt and latch plug from the hole in the door jamb. Then, you are able to install your new lock. If you are replacing a mortise window lock repair cost, you must also measure the distance between the lock case and the door's edge to ensure that the new lock will be able to fit.

There are a variety of reasons that could prompt you to change your door lock, including being concerned that someone else may have the key or welcoming a new roommate. In any event, you could save money by taking the lock off yourself instead of paying an expert to do it. It's easier than many people imagine and can be done in a few minutes.

Remove the trim and handle of your door. Then, pry the trim loose using a screwdriver that is flat. It should be possible to pull off the majority of it. In certain cases you may be able to take off the handles completely. Then, look for a small pinhole on the inside and insert a straightened clip into it. This will activate the release mechanism, allowing you to take off the handle. Look for a small tab that is located inside of the lock and press it using a flat screwdriver. After the spindle has been removed, you can take off the cylinder and the housing.

Selecting a new lock

When it comes to choosing a new lock, you have many options. Take a look at various kinds of locks, and choose one that is compatible with your door's style. Think about the backset (the distance between the door's edge and the center of the window lock repair cost hole) and the cross bore (small hole that runs along the edge of the door frame). Select a lock that will fit the door's thickness and the swing.

The American National Standards Institute and BHMA have graded all door locks to give an idea of their strength and how difficult it is to pick them or disable them. A grade 3 repair upvc window lock may be the ideal choice for a tranquil apartment in the countryside, whereas repair window locks upvc of grade 1 may be more suitable for the busy streets near the storefront.

Most smart door locks need a digital code to open. If you're worried about hacking or other security issues seek out a professional locksmith or the local police department to get advice.

Replace the cylinder

You can easily replace damaged or broken door lock cylinder by doing an easy DIY project. It is important to select the right cylinder and follow the instructions. The first step is to take off the handle or knob if there is one, then unscrew the trim around the base of the lock cylinder with the aid of a screwdriver. After the trim has been removed, you can take off the screws holding the cylinder in position with a flathead. The cylinder is then gently removed away from the door.

Before you install the new cylinder, make sure it's the right length for the door you are using. With a tape measure, measure the distance between the cylinder's center and the left and right sides. Then, purchase a new cylinder with the same measurements. This will prevent cylinders from snapping when the door is hit or the key is stuck inside.

If you have a suitable replacement cylinder, insert it into the door and turn the key. This will align the cylinder with the carriage which is located usually on the outside of the lock. Then, you can loosen the set screw that is supposed to be a few turns inside the head. Also, you will need to loosen the screw on the edge of the door which secures the case in the event that there is one.

After you have removed the lock cylinder and replacing it with a new lock by slipping the new cylinder into the case and tightening the set screw. Installing the part that connects a cylinder to an indicator stem for a lock is also crucial. It is done by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Then, you can connect the remaining smaller bracket to the back of the cylinder. You should then reinstall the latch plate and strike plate, as well as the retaining rings fixed to the top of the lock cylinder.

Installing a new lock

Begin by measuring the door's width if you are replacing an existing lock. Most locksets for residential use have a thickness of 3/8 inch to 1 3/4 inches. If your door is more thick, you will need a door kit that is thick and includes longer screws and an extended tail piece (for door knobs) or spindle extension (for deadbolts).

The majority of locks come with a comprehensive installation guide to help you. Be sure to read the instructions thoroughly before beginning the process to ensure that you are following all the steps. The guide will also provide you with an idea of the level of expertise required to complete the task. It is possible to seek out a friend who has had experience in changing locks for assistance if you are changing locks for the first time.

Before installing the new lock it's an excellent idea to put tape over the openings of the old hardware. This will prevent the screws from slipping through the holes, and also protect any tiles you have installed. It also shields your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a strip painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape if you have it available.

After you have removed the screws that hold the lock's inner half to its exterior and remove the lock immediately. This should be done swiftly to prevent the lock from closing accidentally and damaging the mechanism.

Install the new latch bolt into the upper cross bore of the new lock if it has one. Make sure to place it in the correct position, which is marked by an arrow. Next, fit the latch plate onto the bolt and secure it in place.

Screw the deadbolt to the jamb of the door. Try the deadbolt a few times by throwing it to ensure it is extending into the strike plate. Follow the instructions included in your electronic smart lock to program it. This involves downloading an application, creating an email address, confirming your identity, and then connecting to the wireless network to connect your device.