• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace Door Lock Door Locks

Door locks are the first protection against unauthorised access to your home. The locks may need to be replaced due to wear and tear, or other situations like moving into a new residence or a burglary.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will allow you to purchase the correct-sized lock.

Deadbolt

Installing a deadbolt is great way to secure your door from intruders. The bolt extends into the strike plate on the door frame when it's locked, making it much more difficult for a burglar to gain entry into the door. A single-cylinder deadbolt is activated using a key on the outside and a thumb-turn device situated inside. A deadbolt will only work if it is installed correctly.

It is first necessary to determine if the door has an existing hole for a deadbolt or if you have to bore it out. Mark the location of the hole for the deadbolt on top of the door Replace Door Lock using the template that came with your lock installation set. Utilize your tape measure to determine the height of the deadbolt. Then, mark the height on the side of the door. You can then use a speed square to draw a straight line across the mark you made for the bolt hole.

Next, use a power drill to drill this area until the hole extends to the opposite side of the door. It could take a few minutes. Sand the hole and the edge of the door to make it smooth. It's also a good idea to stain or paint the upvc door locks replacement at this point.

Remove any visible screws from the deadbolt. This will reveal the back and front assemblies of the deadbolt, and also the bolt that is inside. Then, unscrew the bolt and replace it with a new one that matches the door hardware. You'll need to remove the bolt from a setplate. Then, you'll need to chisel the surface of the door frame for the strike plate.

If your strike plate is not in alignment it could be because the previous installer did not mortise it properly, or a weatherstripping has changed the strike position. To fix this problem, you will need to remortise the strike plate and the deadbolt. After this is done Test the deadbolt by closing and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

If the knob on your door is worn out it could make your business or home less secure. It can also make opening or closing the door more difficult, so it's recommended to replace patio door lock it. It shouldn't take longer than 30 minutes. You can use a screwdriver or pliers to remove the knob or handle that was previously used However, be careful not to damage any other parts on the door.

Before starting, you'll want to spray WD-40 or a different dry lubricant on the mechanism of the knob on your door. This will allow the lock to move smoothly when you turn it. To ensure that it operates properly it is important to select the knob and Replace Door Lock handle that match your existing doors. If you don't have a match, you'll need to buy an additional doorknob and latch plate.

Before you begin the replacement process, examine the old knob to determine which screws are holding it in place. If there aren't any screws you can use a screwdriver to wedge between the cover plate and the hidden screws plate and remove it.

After you've removed the old knob, examine it for any signs of rust or damage. It's important to clean it off if you notice any scratches or dents, but you shouldn't have to do anything major when the knob is in good working order.

Install the new knob. You must first study the two knobs in order to make sure that you are choosing the correct one for your door. You should select one with an extending rod that is designed to lock with the rod mechanism of the second knob. After you've placed the new knob into the hole then slide it into the latch.

Test the spring by pressing it repeatedly. The latch should spring up every time. Then, put in the new knob and lock it with the rod mechanism on the previous knob. Thread in the other long screws from the knob's interior through the cylinder hole on the doorknob on the outside and lock it in place.

Latch

A latch is a piece of metal that extends through the door jamb to keep it shut. The latch is operated either by a knob or handle on the inside of the door, or by a thumb-turn on the exterior. A latch can be secured using deadbolts to stop thieves from breaking through the glass. It also provides protection from accidental or intentional closing of the door by pets or children. You can install an entry point with either a single-cylinder deadbolt, or a double glazed door lock replacement-cylinder deadbolt depending on the level of security.

Installing a deadbolt is the same as installing a latch, but there are some differences. First, determine the setback of the doorjamb with an instrument to make sure the new lock will fit. The setback is measured from the edge of the doorjamb up to the middle of the hole for the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If your setback is greater, you may need to purchase an extra-long latch from a hardware or locksmith store.

Then, you'll need to make a hole for the latch plate at the doorjamb's edge. Use a chisel for chiseling out the mortise of the latch making sure it's large enough for the faceplate of the new latch to be close to the doorjamb. Tape the strike plate in place to make sure it's in the right position.

If the strike is positioned too high, the door can be kicked in or pressure imposed on it using a crowbar, or tire iron. This could also cause cracks in the doorjamb. To remedy this, the strike can be lowered by drilling a new hole through the doorjamb, and then cutting out the core of the hole that was previously drilled.

The final step is to install the new strike plate, which can be accomplished by screwing it in place over the existing screw holes. Then apply wood putty to fill in the old screw holes and the bolt hole that won't be used. After the putty is dry, sand it to a smooth finish.

Strike

An electric strike is the metallic piece where the latch and deadbolt engage when the door is shut. It is a crucial component of the security of a lock, because it helps keep the door shut and offers additional resistance to kicking or force applied to the door. If a door is equipped with an electronic strike, it will be opened only by an entry key and a control unit that regulates its electrical impulses.

Traditionally, installing an electric strike required cutting out a portion of the doorjamb to remotely release the latchbolt of a circular lock from the pocket in the strike. This modification is not just undesirable however, it also exposes the mechanism of the latchbolt and keeper to uninitiated users.

Recently, several electric strikes manufacturers have developed a "No Cut" type of strike that does not require a cutout to operate. These strikes have a unique design that allows the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike is fitted with an internal ramp that lifts the latchbolt and keeper whenever it receives an indication from a reader. The latchbolt and keeper are lifted higher on the ramp thanks to the retract. When the door is shut, the deadbolt remains in place and the latchbolt is retracted into the keeper.

Installing an electric strike is an easy task, especially in the case of replacing a strike on an existing door. If you are upgrading an access control system to an electric strike, you must ensure that your new system is compatible. Also, you must ensure that the strike is connected to your access control system and that it is set up for fail-safe operation.

Upgrade your strike plates with heavy duty strike plates to stop the entry of unauthorized persons. The plates are made of up to six screws of three inches instead of the usual two screws of three-fourths inch. These longer screws make it difficult for anyone to break the frame and reach inside to turn the piece that turns the thumb of a single cylinder deadbolt.