• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your primary protection against unauthorised access to your home. Locks may require replacement door lock due to wear and tear or other circumstances such as moving into a new home or a burglary.

To begin, you must determine the size of your cylinder using the distance between the adjustment screw and the center of the cylinder knob. This measurement will allow you to buy the right lock.

Deadbolt

Installing a deadbolt is excellent way to protect your door from intruders. When the bolt is extended into the strike plate of the doorframe, it makes it much more difficult for an intruder to break through the door. A single-cylinder deadbolt is activated using a key on the exterior, and replace Door lock the thumb-turn mechanism that is located inside. A deadbolt will only work only if it is correctly installed.

You will first need to determine whether the door already has an existing hole for a deadbolt, or if you have to bore it out. Utilizing the template included with your lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Mark this height on the door edge. Use the speedsquare to draw a straight line across the mark that you made for the bolt hole.

Then, use a power drill to bore out this spot until the hole reaches the opposite side of the door. It may take a while. Then, sand the hole and the edge of the door until it is smooth. At this point, it's a good idea also to stain or paint your door.

Remove any screws that are visible from the deadbolt. This will reveal the front and back assemblies of the deadbolt and also the bolt that is inside. Then, loosen the bolt and replace it with a new one that matches the door hardware. You will need to unscrew the bolt from the setplate. After that, you'll have to chisel the door frame for the strike plate.

If your strike plate isn't aligned properly it's likely that the previous installer didn't properly mortise it or a weatherstripping came along and changed the strike's position. To fix this issue it is necessary to remortise both the strike plate and the deadbolt. Close and lock the deadbolt once you have completed this step. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

If the knob on your door wears out, it can make your home or business less secure. It could make opening or closing the door more difficult, so it is an ideal idea to replace door lock (Suggested Online site) the knob. It shouldn't take you more than 30 minutes. Use a screwdriver or pliers to take off any knobs or handles. Be careful not to damage other components of the upvc door lock replacements.

Before you begin you'll need to spray WD-40 or some other dry lubricant onto the mechanism of the knob on your door. This will let the new lock to slide effortlessly as you turn it. To ensure that it operates properly, it's important to choose a knob and handle that are compatible with your patio doors locks replacement. If you don't have a match you'll need to purchase a replacement doorknob and latch plate.

To begin the replacement locks for patio doors process, look at the knob or handle to find the screws that hold it in place. If there aren't screws, you can use the screwdriver to wedge the cover plate in between the screws plate that is hidden.

After taking the knob off examine it for evidence of damage or rust. If the knob shows any dents or marks it's time clean it. Otherwise it shouldn't need any major work.

It's time to install the new one. You must first study the two knobs to make sure that you've chosen the right one for the door. You should select one that has an extending rod designed to interlock with the second knob's rod mechanism. Once you've put the new knob into the hole, slide it into the latch.

Thread the latch plate screws downwards and test the spring by pressing down repeatedly. The latch should rise every time. Install the second knob and lock it to the rod mechanism of the first knob. Attach the other long screws from the interior knob through the hole for the cylinder on the doorknob outside and lock it in place.

Latch

A latch is a piece metal that extends into the doorjamb to secure it closed. The latch is operated by a knob or handle on the inside of the door, or a thumb-turn on the outside. A latch can be secured by a deadbolt to keep intrusions from piercing the glass of the door. It can also guard against the accidental or deliberate closing by children or animals. It is possible to install a latch with either a single-cylinder deadbolt or double-cylinder deadbolt, depending on the level you prefer for security.

Installing a latch involves the same steps similar to installing a deadbolt however, there are a few variations. To make sure that the new lock will work, first determine the setback of the doorjamb using a tape measure. The setback is the distance between the edge of the doorjamb, to the center of the hole for the faceplate for the latch. The standard setback is 2 3/8 to 2. 3/4 inches. If you have a larger setback, you might need to purchase a larger latch from a hardware store or locksmith.

The next step is to drill an edge bore hole through the doorjamb for the latch plate. Utilize a chisel to smooth out the mortise for the latch making sure it's large enough to allow the faceplate of the new latch to be close to the doorjamb. Tape the strikeplate to the doorjamb to ensure that it's positioned correctly.

If the strike is set too high, the door could be pushed into or pressure applied to it using a crowbar or tire iron. This could cause the doorjamb to crack. To remedy this, the strike could be lowered by drilling another hole into the doorjamb and chiseling out the center of the previous hole.

Installing the new strike plate is the last step. This can be done by screwing the new plate over the existing screwholes. Then you can use wood putty to fill in the old screw holes and the bolt hole that will not be used. Once the putty is dry then sand it to a smooth finish for a professional finish.

Strike

An electric strike is a metal piece that holds the deadbolt and latch engage when the door is shut. It is a crucial component of the security of a lock, since it seals the door and also provides additional resistance to force or kicking applied to the door. If a door comes with an electronic strike, it can be opened by using keys and the control unit that regulates its electrical impulses.

Traditionally the installation of an electric strike involved cutting out a portion of the doorjamb to remotely remove the latchbolt of a circular lock from the pocket within the strike. This modification can be a drawback in terms of the aesthetics of an opening as well as exposing the mechanism of the latchbolt and keeper to unauthorized users.

Recently, several electric strike manufacturers have developed a brand new electric strike dubbed the "No Cut" strike that doesn't need cutouts in the doorjamb to function. The strikes have a unique design that allows the latchbolt and Replace Door Lock keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike has an internal ramp which lifts the latchbolt and keeper whenever it receives a signal from the reader. The keeper and latchbolt are pushed higher on the ramp thanks to the retract. When the door is closed the deadbolt remains retracted and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy process, particularly when you are replacing lock in upvc door an existing strike door. However, if you're upgrading to an electric strike for an access control system, you will be required to ensure that the new system is compatible with the model of lock you have installed. It is also necessary to make sure that the strike is properly connected to your access control system and is set up to function in a fail-safe manner.

Upgrade your strike plates with heavy duty strike plates to stop the entry of unauthorized persons. These plates use four to six screws of three inches instead of the two, three-fourth inch screws typically used in regular strikes. These screws are longer and make breaking the frame to reach the thumb turn piece on a single deadbolt cylinder more difficult.