• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your primary line of defense against unauthorized entry into your home. Signs of wear and tear and also instances like moving into a new house or burglaries, could trigger the need to replace your lock.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will assist you purchase the right-sized lock.

Deadbolt

Installing a deadbolt is a great way to secure your door from intruders. The bolt extends into the strike plate on the door frame when it's locked, making it more difficult for a burglar to gain entry through the door. A single-cylinder deadbolt can be activated with a key on the exterior, and a thumb-turn piece that is located inside. Deadbolts are only effective only if it's correctly installed, though.

First, you'll need to determine if the door has a hole for deadbolts or has to be bored. Using the template that comes with the lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Then, you can use your tape measure to determine the height the deadbolt should be. Then, mark the high point on the outside of the door and use a speed square to draw a straight line across the mark you made for the bolt hole.

Then by using a power drill, bore through the hole until it reaches the opposite side of the door. It could take a few minutes. Then, sand down the hole and the edges of the door so that it's smooth. At this point, it's a good idea also to stain or paint your replacing patio door lock.

Remove any screws that are visible from the deadbolt. This will reveal the front and back assemblies of the deadbolt and also the bolt that is inside. Then, remove the bolt and replace it with a new one that matches the door hardware. You will need to unscrew the bolt from the setplate. After that it is time to chisel out the area for the strike plate that is on the upvc door locks replacement frame.

If your strike plate is out of alignment It could be due to the previous installer did not mortise it correctly or an installation of a weatherstripping altered the strike position. To fix this problem it is necessary to remortise the strike plate as well as the deadbolt. Close and lock the deadbolt once you have completed this step. Be sure the bolt is extending into the strike plate and then test the key to make sure it closes and opens easily.

Knob

It can make your home or business less secure if the door knob is worn. It could also make opening or closing the door more difficult, which is why it is a good idea for you to replace it. It shouldn't take you more than 30 minutes. You can use a screwdriver as well as pliers to get rid of the knob or handle However, be careful not to harm any of the other components on the door.

Spray WD-40, or another dry lubricant, onto the mechanism of your door knob before you begin. This will help the new lock slide smoothly as you turn it. It's essential to select a quality knob and handle that is compatible with your doors currently in order to ensure proper operation. If there's no match you'll need to purchase an additional doorknob and latch plate.

Before you begin the replacement locks for patio doors, examine the old knob to determine what screws are holding it in place. If there aren't screws to hold it in place, you can use a screwdriver to insert the cover plate between the hidden screws plate.

Once you've removed the knob that was previously used, look it over for signs of rust or damage. If the knob is damaged or has marks or scratches, you'll have to clean it. Otherwise, it shouldn't require any major work.

Install the new knob. You must first study the two knobs to ensure that you are choosing the right one for the door. You'll need to choose one with an extending rod that will interlock with the rod mechanism of the other knob. After you've inserted the new knob into the hole and then put it in the latch.

Thread the latch plate screws downwards and test the spring by pressing down several times. The latch should then spring back up every time. Then, you can install the new knob and connect it with the rod mechanism on the first knob. Attach the other long screws from the interior knob through the cylinder hole on the doorknob on the outside and secure it.

Latch

A latch is a piece metal that extends into the doorjamb to secure it closed. The latch is operated by a knob or handle on the interior of the door, or a thumb-turn on the exterior. A deadbolt can be used to secure a latch and prevent intruders from breaking through the glass of the door. It also offers protection from accidental or intentional closing of the door by pets or children. You can install an entry point with either a single-cylinder deadbolt, or a double-cylinder deadbolt based on your preferred level of security.

Installing a deadbolt can be the same as installing a latch, however there are some differences. To ensure that the new lock will work first, you must determine the setback of the doorjamb using the tape measure. The setback is measured from the edge of doorjamb all the way to the center of hole for [Redirect Only] the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If your setback is greater, you may need to purchase a latch that is larger from a locksmith or hardware store.

Then, drill a hole for the latch plate in the edge of the doorjamb. Use a chisel to chisel out the latch mortise, making sure it's deep enough to allow the faceplate of the new latch to sit flush with the doorjamb. Tape the strikeplate to the doorjamb to ensure it's placed correctly.

If the strike is set too high, the door may be pushed into or pressure applied to it using a crowbar or tire iron. This could also cause cracks in the doorjamb. To correct this issue, [Redirect-302] the strike can be lowered by drilling another hole into the doorjamb and chiseling out the core of the previous hole.

Installing the new strike plate is the final step. This can be done by screwing the new plate over the existing screwholes. Use wood putty then to fill in any old screw holes or bolt holes that aren't being used. After the putty is dry then sand it to an even finish.

Strike

The piece of metal that connects the latch and deadbolt when the composite door lock replacement is shut is an electric strike. It is an essential component of the lock's overall safety because it stops the door from opening, and also provides an additional barrier to force or kicking. If a door is equipped with an electric strike, it can be opened using a key or the control unit that controls the electrical impulses.

Traditionally the installation of an electric strike meant cutting a section of the doorjamb in order to remotely remove a cylindrical lock's latchbolt from the pocket in the strike. This modification is not just ugly however, it also exposes the mechanism of the latchbolt and the keeper to intruders.

Recently, several electric strikes manufacturers have developed a "No Cut" kind of strike that does not require a cutout to operate. The strikes use a unique design to allow the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike is fitted with an internal ramp that lifts the latchbolt and keeper when it receives an indication from a reader. The retraction of the keeper and latchbolt causes them to rise on the ramp, which locks the door. When the door is closed the deadbolt remains in place and the latchbolt is retracted into the keeper.

Installing an electric strike can be an easy task, especially in the case of replacing upvc Door locks the strike on a previous door. If you're planning to upgrade an existing access control system to an electric strike, it is important cost to replace upvc door lock mechanism near me ensure that your new system is compatible. You will also have to ensure that the strike is connected to your access control system and is configured to function in a safe manner.

Upgrade your strike plates with heavy duty strike plates to block unauthorised entry. The plates are made of up to six screws of three inches instead of the standard two screws of three-fourths inch. The longer screws make it difficult for someone to break the frame and reach inside to turn the thumb turn piece of a single cylinder deadbolt.